Description
xShop Now Genuine Lamborghini & Audi Rear Tie Rod Online – Part 4S0501529B
The Genuine Bentley Tie Rod 4S0501529B keeps that angle precise and stable. Suspension geometry on your Bentley controls stability, grip, and tyre wear at all times.
The tie rod sets and holds the rear wheel toe angle under driving loads.
This is a real Bentley OEM tie rod made for rear suspension use. It controls toe angle through the full range of suspension movement. It keeps the rear wheel pointing correctly at all ride heights.
This control helps maintain straight driving and stable cornering balance. A worn tie rod adds play to the suspension and affects toe accuracy. The rear may feel loose during braking or cornering under load.
You may also see uneven tyre wear on the inner or outer edges. This OEM rod has the correct length and joint design for your setup. It fits properly and restores the intended suspension geometry.
A full wheel alignment is required after installation for correct settings. Get the genuine Bentley tie rod today from European Auto Spares.
Specifications
-
Brand: Genuine Bentley OEM
-
Part Number: 4S0501529B
-
Type: Tie Rod (Rear Suspension Toe Link)
-
Material: OEM-grade forged rod with precision ball joint ends and correct thread specification
-
Condition: Brand new, genuine OEM
Why Choose EuropeanAutoSpare?
Genuine OEM Quality
This is a real Bentley tie rod. Rod length and ball joint taper match your Bentley's rear suspension geometry for correct toe maintenance throughout the full suspension travel range.
Perfect Fit
Connects to the subframe and hub carrier with the correct taper and thread at both ends. No modification and no adjustment outside the standard alignment procedure required.
Clean Cabin Air
A correctly set rear toe reduces rear tyre scrub and road debris projection toward the rear wheel arches. This limits debris ingestion near rear cabin air management points.
Full Climate Efficiency
Correct rear toe reduces rolling resistance from tyre scrub, improves straight-line tracking, and extends rear tyre life all of which contribute to driving efficiency in daily UAE use.
Fast Delivery
EuropeanAutoSpare ships this genuine Bentley part fast to the UAE and worldwide with suspension position and model confirmation before dispatch.
Need Help Finding the Right Parts?
EuropeanAutoSpare uses your VIN to confirm the correct tie rod specification for your Bentley model and rear suspension configuration.
Restore Rear Suspension Geometry to Factory Precision
A genuine Bentley Tie Rod 4S0501529B holds your rear toe angle at the designed value throughout every suspension movement. Always follow fitment with a full four-wheel alignment to restore the correct geometry setting.
Fitment Details
xRear Suspension Trailing Link Fitment Guide
| Model / Generation | Application Details (Rear Suspension Trailing Link) | Year Range |
|---|---|---|
| Bentley Continental GT | 6.0L Twin-Turbo W12 Mulliner / GT Speed Models Performance Spec Link | 2021–2026 |
| Lamborghini Huracán | LP610-4 / LP580-2 / Performante / EVO / STO / Tecnica Track Spec Link | 2015–2024 |
| Audi R8 (Type 4S) | 5.2L FSI V10 Coupe & Spyder Generations Track Spec Link | 2016–2024 |
Technician’s Advisory: The rear trailing links across these high-performance architectures are position-specific and precisely matched to the factory track width and dynamic roll-center roll characteristics. When installing a replacement trailing arm, never complete the final torque sequence on the mounting hardware while the suspension is completely unloaded. The rear suspension must be compressed to its normal static ride height before tightening the fasteners; skipping this procedure pre-loads the elastomeric bushings, causing immediate tearing and accelerated bushing deflection within less than a few thousand miles of operation.
FAQs
xFrequently Asked Questions
Yes, this is a genuine Bentley OEM rear control tracking tie rod (Part No. 4S0501529B). It is engineered strictly to original Crewe structural standards, utilizing high-tensile alloys and factory-bonded low-friction joints to preserve optimal chassis response and lateral tracking geometry.
Yes, without exception. The rear tie rod directly governs the vehicle's rear toe alignment tracking angles. Replacing any linked suspension component completely alters these fine tolerances; a full four-wheel laser chassis alignment is required post-installation to reset the toe values back to factory specification and prevent severe handling imbalances.
Typical indications of tie rod bearing fatigue or loose internal ball joints include noticeable rear-end instability or "swaying" during combined cornering and braking loops, highly accelerated, uneven rear tire wear concentrated on a single shoulder edge, or an audible clunking or rattling sound from the rear subframe when tracking over low-speed bumps.
While not mandatory, it is highly recommended practice. Left and right axle links navigate identical road surfaces and mileage friction loads. If an internal ball joint or bushing has deteriorated on one side, the opposite link has likely sustained similar structural fatigue. Replacing them as a paired axle set guarantees uniform tracking dynamics and prevents a redundant return workshop visit.
Yes, European Auto Spares provides fast, fully-tracked express shipping straight to the UAE and worldwide. We pack each suspension rod inside protective anti-mar sleeve wraps and secure them within reinforced, high-burst strength outer boxes to isolate the precision threads, integrated boots, and mounting bushings from any transit shifting or impact forces.
Found It Cheaper.?
xShipping & Return
xReturns Policy
You may return most new, unopened items within 30 days of delivery for a full refund. We'll also pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.).
You should expect to receive your refund within four weeks of giving your package to the return shipper, however, in many cases you will receive a refund more quickly. This time period includes the transit time for us to receive your return from the shipper (5 to 10 business days), the time it takes us to process your return once we receive it (3 to 5 business days), and the time it takes your bank to process our refund request (5 to 10 business days).
If you need to return an item, simply login to your account, view the order using the "Complete Orders" link under the My Account menu and click the Return Item(s) button. We'll notify you via e-mail of your refund once we've received and processed the returned item.
Shipping
We can ship to virtually any address in the world. Note that there are restrictions on some products, and some products cannot be shipped to international destinations.
When you place an order, we will estimate shipping and delivery dates for you based on the availability of your items and the shipping options you choose. Depending on the shipping provider you choose, shipping date estimates may appear on the shipping quotes page.
Please also note that the shipping rates for many items we sell are weight-based. The weight of any such item can be found on its detail page. To reflect the policies of the shipping companies we use, all weights will be rounded up to the next full pound.
- Choosing a selection results in a full page refresh.
